diff options
Diffstat (limited to 'drivers/net/ethernet/stmicro/stmmac')
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 2 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c | 42 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac.h | 2 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 36 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c | 3 |
5 files changed, 46 insertions, 39 deletions
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c index 617d0e4c6495..09644ab0d87a 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c @@ -756,7 +756,7 @@ static int sun8i_dwmac_reset(struct stmmac_priv *priv) if (err) { dev_err(priv->device, "EMAC reset timeout\n"); - return -EFAULT; + return err; } return 0; } diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c index e2e0f977875d..dde5b772a5af 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c @@ -22,21 +22,21 @@ #define ETHER_CLK_SEL_RMII_CLK_EN BIT(2) #define ETHER_CLK_SEL_RMII_CLK_RST BIT(3) #define ETHER_CLK_SEL_DIV_SEL_2 BIT(4) -#define ETHER_CLK_SEL_DIV_SEL_20 BIT(0) +#define ETHER_CLK_SEL_DIV_SEL_20 0 #define ETHER_CLK_SEL_FREQ_SEL_125M (BIT(9) | BIT(8)) #define ETHER_CLK_SEL_FREQ_SEL_50M BIT(9) #define ETHER_CLK_SEL_FREQ_SEL_25M BIT(8) #define ETHER_CLK_SEL_FREQ_SEL_2P5M 0 -#define ETHER_CLK_SEL_TX_CLK_EXT_SEL_IN BIT(0) +#define ETHER_CLK_SEL_TX_CLK_EXT_SEL_IN 0 #define ETHER_CLK_SEL_TX_CLK_EXT_SEL_TXC BIT(10) #define ETHER_CLK_SEL_TX_CLK_EXT_SEL_DIV BIT(11) -#define ETHER_CLK_SEL_RX_CLK_EXT_SEL_IN BIT(0) +#define ETHER_CLK_SEL_RX_CLK_EXT_SEL_IN 0 #define ETHER_CLK_SEL_RX_CLK_EXT_SEL_RXC BIT(12) #define ETHER_CLK_SEL_RX_CLK_EXT_SEL_DIV BIT(13) -#define ETHER_CLK_SEL_TX_CLK_O_TX_I BIT(0) +#define ETHER_CLK_SEL_TX_CLK_O_TX_I 0 #define ETHER_CLK_SEL_TX_CLK_O_RMII_I BIT(14) #define ETHER_CLK_SEL_TX_O_E_N_IN BIT(15) -#define ETHER_CLK_SEL_RMII_CLK_SEL_IN BIT(0) +#define ETHER_CLK_SEL_RMII_CLK_SEL_IN 0 #define ETHER_CLK_SEL_RMII_CLK_SEL_RX_C BIT(16) #define ETHER_CLK_SEL_RX_TX_CLK_EN (ETHER_CLK_SEL_RX_CLK_EN | ETHER_CLK_SEL_TX_CLK_EN) @@ -96,31 +96,41 @@ static void visconti_eth_fix_mac_speed(void *priv, unsigned int speed) val |= ETHER_CLK_SEL_TX_O_E_N_IN; writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); + /* Set Clock-Mux, Start clock, Set TX_O direction */ switch (dwmac->phy_intf_sel) { case ETHER_CONFIG_INTF_RGMII: val = clk_sel_val | ETHER_CLK_SEL_RX_CLK_EXT_SEL_RXC; + writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); + + val |= ETHER_CLK_SEL_RX_TX_CLK_EN; + writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); + + val &= ~ETHER_CLK_SEL_TX_O_E_N_IN; + writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); break; case ETHER_CONFIG_INTF_RMII: val = clk_sel_val | ETHER_CLK_SEL_RX_CLK_EXT_SEL_DIV | - ETHER_CLK_SEL_TX_CLK_EXT_SEL_TXC | ETHER_CLK_SEL_TX_O_E_N_IN | + ETHER_CLK_SEL_TX_CLK_EXT_SEL_DIV | ETHER_CLK_SEL_TX_O_E_N_IN | ETHER_CLK_SEL_RMII_CLK_SEL_RX_C; + writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); + + val |= ETHER_CLK_SEL_RMII_CLK_RST; + writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); + + val |= ETHER_CLK_SEL_RMII_CLK_EN | ETHER_CLK_SEL_RX_TX_CLK_EN; + writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); break; case ETHER_CONFIG_INTF_MII: default: val = clk_sel_val | ETHER_CLK_SEL_RX_CLK_EXT_SEL_RXC | - ETHER_CLK_SEL_TX_CLK_EXT_SEL_DIV | ETHER_CLK_SEL_TX_O_E_N_IN | - ETHER_CLK_SEL_RMII_CLK_EN; + ETHER_CLK_SEL_TX_CLK_EXT_SEL_TXC | ETHER_CLK_SEL_TX_O_E_N_IN; + writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); + + val |= ETHER_CLK_SEL_RX_TX_CLK_EN; + writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); break; } - /* Start clock */ - writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); - val |= ETHER_CLK_SEL_RX_TX_CLK_EN; - writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); - - val &= ~ETHER_CLK_SEL_TX_O_E_N_IN; - writel(val, dwmac->reg + REG_ETHER_CLOCK_SEL); - spin_unlock_irqrestore(&dwmac->lock, flags); } diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h index 40b5ed94cb54..5b195d5051d6 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h @@ -194,7 +194,6 @@ struct stmmac_priv { u32 tx_coal_timer[MTL_MAX_TX_QUEUES]; u32 rx_coal_frames[MTL_MAX_TX_QUEUES]; - int tx_coalesce; int hwts_tx_en; bool tx_path_in_lpi_mode; bool tso; @@ -229,7 +228,6 @@ struct stmmac_priv { unsigned int flow_ctrl; unsigned int pause; struct mii_bus *mii; - int mii_irq[PHY_MAX_ADDR]; struct phylink_config phylink_config; struct phylink *phylink; diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 6708ca2aa4f7..639a753266e6 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -402,7 +402,7 @@ static void stmmac_lpi_entry_timer_config(struct stmmac_priv *priv, bool en) * Description: this function is to verify and enter in LPI mode in case of * EEE. */ -static void stmmac_enable_eee_mode(struct stmmac_priv *priv) +static int stmmac_enable_eee_mode(struct stmmac_priv *priv) { u32 tx_cnt = priv->plat->tx_queues_to_use; u32 queue; @@ -412,13 +412,14 @@ static void stmmac_enable_eee_mode(struct stmmac_priv *priv) struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue]; if (tx_q->dirty_tx != tx_q->cur_tx) - return; /* still unfinished work */ + return -EBUSY; /* still unfinished work */ } /* Check and enter in LPI mode */ if (!priv->tx_path_in_lpi_mode) stmmac_set_eee_mode(priv, priv->hw, priv->plat->en_tx_lpi_clockgating); + return 0; } /** @@ -450,8 +451,8 @@ static void stmmac_eee_ctrl_timer(struct timer_list *t) { struct stmmac_priv *priv = from_timer(priv, t, eee_ctrl_timer); - stmmac_enable_eee_mode(priv); - mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer)); + if (stmmac_enable_eee_mode(priv)) + mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer)); } /** @@ -889,6 +890,9 @@ static int stmmac_init_ptp(struct stmmac_priv *priv) bool xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac; int ret; + if (priv->plat->ptp_clk_freq_config) + priv->plat->ptp_clk_freq_config(priv); + ret = stmmac_init_tstamp_counter(priv, STMMAC_HWTS_ACTIVE); if (ret) return ret; @@ -911,8 +915,6 @@ static int stmmac_init_ptp(struct stmmac_priv *priv) priv->hwts_tx_en = 0; priv->hwts_rx_en = 0; - stmmac_ptp_register(priv); - return 0; } @@ -2647,8 +2649,8 @@ static int stmmac_tx_clean(struct stmmac_priv *priv, int budget, u32 queue) if (priv->eee_enabled && !priv->tx_path_in_lpi_mode && priv->eee_sw_timer_en) { - stmmac_enable_eee_mode(priv); - mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer)); + if (stmmac_enable_eee_mode(priv)) + mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(priv->tx_lpi_timer)); } /* We still have pending packets, let's call for a new scheduling */ @@ -3238,7 +3240,7 @@ static int stmmac_fpe_start_wq(struct stmmac_priv *priv) /** * stmmac_hw_setup - setup mac in a usable state. * @dev : pointer to the device structure. - * @init_ptp: initialize PTP if set + * @ptp_register: register PTP if set * Description: * this is the main function to setup the HW in a usable state because the * dma engine is reset, the core registers are configured (e.g. AXI, @@ -3248,7 +3250,7 @@ static int stmmac_fpe_start_wq(struct stmmac_priv *priv) * 0 on success and an appropriate (-)ve integer as defined in errno.h * file on failure. */ -static int stmmac_hw_setup(struct net_device *dev, bool init_ptp) +static int stmmac_hw_setup(struct net_device *dev, bool ptp_register) { struct stmmac_priv *priv = netdev_priv(dev); u32 rx_cnt = priv->plat->rx_queues_to_use; @@ -3305,13 +3307,13 @@ static int stmmac_hw_setup(struct net_device *dev, bool init_ptp) stmmac_mmc_setup(priv); - if (init_ptp) { - ret = stmmac_init_ptp(priv); - if (ret == -EOPNOTSUPP) - netdev_warn(priv->dev, "PTP not supported by HW\n"); - else if (ret) - netdev_warn(priv->dev, "PTP init failed\n"); - } + ret = stmmac_init_ptp(priv); + if (ret == -EOPNOTSUPP) + netdev_warn(priv->dev, "PTP not supported by HW\n"); + else if (ret) + netdev_warn(priv->dev, "PTP init failed\n"); + else if (ptp_register) + stmmac_ptp_register(priv); priv->eee_tw_timer = STMMAC_DEFAULT_TWT_LS; diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c index 0d24ebd37873..1c9f02f9c317 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c @@ -297,9 +297,6 @@ void stmmac_ptp_register(struct stmmac_priv *priv) { int i; - if (priv->plat->ptp_clk_freq_config) - priv->plat->ptp_clk_freq_config(priv); - for (i = 0; i < priv->dma_cap.pps_out_num; i++) { if (i >= STMMAC_PPS_MAX) break; |
