| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to the i.MX23/28 reference manuals both mmc interfaces support
the MMC_ERASE command. So enable this capability in the driver to allow
erase/discard/trim requests.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case spi_sync_locked fails, the fix reports the error and
returns the error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For some controllers, in Present State Register, Data Line
Active bit is not reliable for commands (such as CMD6, CMD7,
CMD12, CMD28, CMD29, or CMD38) with busy signal. DLA affects
Command with Data Inhibit bit. Therefore, software driver
may not know the busy status in DLA/CDIHB.
Futunately MMC core driver has already polled card status
with CMD13 after sending any command with busy signal. So
we can just ignore CDIHB never released issue for such
controllers. This patch is to add a quirk to handle this.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Invalid Transfer Complete (IRQSTAT[TC]) bit could be set during
multi-write operation even when the BLK_CNT in BLKATTR register
has not reached zero. Therefore, Transfer Complete might be
reported twice due to this erratum since a valid Transfer Complete
occurs when BLK_CNT reaches zero. This erratum is to fix this issue
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the event of that any data error (like, IRQSTAT[DCE]) occurs
during an eSDHC data transaction where DMA is used for data
transfer to/from the system memory, setting the SYSCTL[RSTD]
register may cause a system hang. If software sets the register
SYSCTL[RSTD] to 1 for error recovery while DMA transferring is
not complete, eSDHC may hang the system bus. This happens because
the software register SYSCTL[RSTD] resets the DMA engine without
waiting for the completion of pending system transactions. This
erratum is to fix this issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not
reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock),
and 0xC(2^25 SD clock). The data timeout counter can count from
2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout
counter counts for only 2^13 SD clocks.
A-008358: The data timeout counter value loaded into the timeout
counter is less than expected and can result into early timeout
error in case of eSDHC data transactions. The table below shows
the expected vs actual timeout period for different values of
SYSCTL[DTOCV]:
these two erratum has the same quirk to control it, and set
SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Software writing to the Transfer Type configuration register
(system clock domain) can cause a setup/hold violation in the
CRC flops (card clock domain), which can cause write accesses
to be sent with corrupt CRC values. This issue occurs only for
write preceded by read. this erratum is to fix this issue.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch is to add erratum A011334 support in lx2160 2.0 SoC
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As mmci_variant_init() is a local function to mmci.c, let's convert it into
static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It's good practice to share functions via header files, rather than from
the c-files. Therefore, let's move sdmmc_variant_init() to mmci.h.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It seems a bit silly to have a header file to share only the
qcom_variant_init() function. So, let's just drop it and move the
declaration of the function into the common mmci.h instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Having mmci_dmae_start() to invoke the shared function, dml_start_xfer(),
explicitly for the qcom variant isn't very nice. Let's clean up this code
by moving the qcom specific parts into the qcom ->dma_start() callback and
then drop dml_start_xfer() altogether.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There's no point clearing the variant flag in case the qcom variant fails
to setup DMA. This is because if mmci_dma_setup() fails, then the use_dma
flag remains set to false, which leads to mmci using PIO mode and not DMA.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some of the DMA functions are shared via mmci.h, however they are not
implemented unless CONFIG_DMA_ENGINE is set. Therefore, add that constraint
to the header file as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
Change pipe_buf_get() to return a bool indicating whether it succeeded
in raising the refcount of the page (if the thing in the pipe is a page).
This removes another mechanism for overflowing the page refcount. All
callers converted to handle a failure.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the page refcount wraps around past zero, it will be freed while
there are still four billion references to it. One of the possible
avenues for an attacker to try to make this happen is by doing direct IO
on a page multiple times. This patch makes get_user_pages() refuse to
take a new page reference if there are already more than two billion
references to the page.
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the same as the traditional 'get_page()' function, but instead
of unconditionally incrementing the reference count of the page, it only
does so if the count was "safe". It returns whether the reference count
was incremented (and is marked __must_check, since the caller obviously
has to be aware of it).
Also like 'get_page()', you can't use this function unless you already
had a reference to the page. The intent is that you can use this
exactly like get_page(), but in situations where you want to limit the
maximum reference count.
The code currently does an unconditional WARN_ON_ONCE() if we ever hit
the reference count issues (either zero or negative), as a notification
that the conditional non-increment actually happened.
NOTE! The count access for the "safety" check is inherently racy, but
that doesn't matter since the buffer we use is basically half the range
of the reference count (ie we look at the sign of the count).
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We have a VM_BUG_ON() to check that the page reference count doesn't
underflow (or get close to overflow) by checking the sign of the count.
That's all fine, but we actually want to allow people to use a "get page
ref unless it's already very high" helper function, and we want that one
to use the sign of the page ref (without triggering this VM_BUG_ON).
Change the VM_BUG_ON to only check for small underflows (or _very_ close
to overflowing), and ignore overflows which have strayed into negative
territory.
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Code which initializes the "clk_init_data.ops" checks pll->rate_table
before that field is ever assigned to so it always picks
"clk_pll1416x_min_ops".
This breaks dynamic rate rounding for features such as cpufreq.
Fix by checking pll_clk->rate_table instead, here pll_clk refers to
the constant initialization data coming from per-soc clk driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7fb ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
CLK_SET_RATE_PARENT would be dropped.
Merge two flag setting together to correct the error.
Fixes: 5a1cc4c27ad2 ("clk: mediatek: Add flags to mtk_gate")
Cc: <stable@vger.kernel.org>
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Rather embarrassingly, our futex() FUTEX_WAKE_OP implementation doesn't
explicitly set the return value on the non-faulting path and instead
leaves it holding the result of the underlying atomic operation. This
means that any FUTEX_WAKE_OP atomic operation which computes a non-zero
value will be reported as having failed. Regrettably, I wrote the buggy
code back in 2011 and it was upstreamed as part of the initial arm64
support in 2012.
The reasons we appear to get away with this are:
1. FUTEX_WAKE_OP is rarely used and therefore doesn't appear to get
exercised by futex() test applications
2. If the result of the atomic operation is zero, the system call
behaves correctly
3. Prior to version 2.25, the only operation used by GLIBC set the
futex to zero, and therefore worked as expected. From 2.25 onwards,
FUTEX_WAKE_OP is not used by GLIBC at all.
Fix the implementation by ensuring that the return value is either 0
to indicate that the atomic operation completed successfully, or -EFAULT
if we encountered a fault when accessing the user mapping.
Cc: <stable@kernel.org>
Fixes: 6170a97460db ("arm64: Atomic operations")
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The exlcusion range limit register needs to contain the
base-address of the last page that is part of the range, as
bits 0-11 of this register are treated as 0xfff by the
hardware for comparisons.
So correctly set the exclusion range in the hardware to the
last page which is _in_ the range.
Fixes: b2026aa2dce44 ('x86, AMD IOMMU: add functions for programming IOMMU MMIO space')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Re-run the shell fragment that generated the original list now that
there are two dozens of new entries after v5.1's merge window.
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
Thomas-Mich Richter reported he triggered a WARN()ing from event_function_local()
on his s390. The problem boils down to:
CPU-A CPU-B
perf_event_overflow()
perf_event_disable_inatomic()
@pending_disable = 1
irq_work_queue();
sched-out
event_sched_out()
@pending_disable = 0
sched-in
perf_event_overflow()
perf_event_disable_inatomic()
@pending_disable = 1;
irq_work_queue(); // FAILS
irq_work_run()
perf_pending_event()
if (@pending_disable)
perf_event_disable_local(); // WHOOPS
The problem exists in generic, but s390 is particularly sensitive
because it doesn't implement arch_irq_work_raise(), nor does it call
irq_work_run() from it's PMU interrupt handler (nor would that be
sufficient in this case, because s390 also generates
perf_event_overflow() from pmu::stop). Add to that the fact that s390
is a virtual architecture and (virtual) CPU-A can stall long enough
for the above race to happen, even if it would self-IPI.
Adding a irq_work_sync() to event_sched_in() would work for all hardare
PMUs that properly use irq_work_run() but fails for software PMUs.
Instead encode the CPU number in @pending_disable, such that we can
tell which CPU requested the disable. This then allows us to detect
the above scenario and even redirect the IPI to make up for the failed
queue.
Reported-by: Thomas-Mich Richter <tmricht@linux.ibm.com>
Tested-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If the last bio returned is not dio->bio, the status of the bio will
not assigned to dio->bio if it is error. This will cause the whole IO
status wrong.
ksoftirqd/21-117 [021] ..s. 4017.966090: 8,0 C N 4883648 [0]
<idle>-0 [018] ..s. 4017.970888: 8,0 C WS 4924800 + 1024 [0]
<idle>-0 [018] ..s. 4017.970909: 8,0 D WS 4935424 + 1024 [<idle>]
<idle>-0 [018] ..s. 4017.970924: 8,0 D WS 4936448 + 321 [<idle>]
ksoftirqd/21-117 [021] ..s. 4017.995033: 8,0 C R 4883648 + 336 [65475]
ksoftirqd/21-117 [021] d.s. 4018.001988: myprobe1: (blkdev_bio_end_io+0x0/0x168) bi_status=7
ksoftirqd/21-117 [021] d.s. 4018.001992: myprobe: (aio_complete_rw+0x0/0x148) x0=0xffff802f2595ad80 res=0x12a000 res2=0x0
We always have to assign bio->bi_status to dio->bio.bi_status because we
will only check dio->bio.bi_status when we return the whole IO to
the upper layer.
Fixes: 542ff7bf18c6 ("block: new direct I/O implementation")
Cc: stable@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 009a82f6437490c262584d65a14094a818bcb747.
The ability to optimise here relies on compiler being able to optimise
away tail calls to avoid stack overflows. Unfortunately, we are seeing
reports of problems, so let's just revert.
Reported-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
According to the NFSv4.2 spec if the input and output file is the
same file, operation should fail with EINVAL. However, linux
copy_file_range() system call has no such restrictions. Therefore,
in such case let's return EOPNOTSUPP and allow VFS to fallback
to doing do_splice_direct(). Also when copy_file_range is called
on an NFSv4.0 or 4.1 mount (ie., a server that doesn't support
COPY functionality), we also need to return EOPNOTSUPP and
fallback to a regular copy.
Fixes xfstest generic/075, generic/091, generic/112, generic/263
for all NFSv4.x versions.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
We want to drain only the RQ first. Otherwise the transport can
deadlock on ->close if there are outstanding Send completions.
Fixes: 6d2d0ee27c7a ("xprtrdma: Replace rpcrdma_receive_wq ... ")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
NFSv4 GETACL and FS_LOCATIONS requests stopped working in v5.1-rc.
These two need the extra padding to be added directly to the reply
length.
Reported-by: Olga Kornievskaia <aglo@umich.edu>
Fixes: 02ef04e432ba ("NFS: Account for XDR pad of buf->pages")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Olga Kornievskaia <aglo@umich.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
syzbot is reporting uninitialized value at rpc_sockaddr2uaddr() [1]. This
is because syzbot is setting AF_INET6 to "struct sockaddr_in"->sin_family
(which is embedded into user-visible "struct nfs_mount_data" structure)
despite nfs23_validate_mount_data() cannot pass sizeof(struct sockaddr_in6)
bytes of AF_INET6 address to rpc_sockaddr2uaddr().
Since "struct nfs_mount_data" structure is user-visible, we can't change
"struct nfs_mount_data" to use "struct sockaddr_storage". Therefore,
assuming that everybody is using AF_INET family when passing address via
"struct nfs_mount_data"->addr, reject if its sin_family is not AF_INET.
[1] https://syzkaller.appspot.com/bug?id=599993614e7cbbf66bc2656a919ab2a95fb5d75c
Reported-by: syzbot <syzbot+047a11c361b872896a4f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
With skip set to 1, I get a traceback like this:
[ 106.867637] DMA-API: Mapped at:
[ 106.870784] afu_dma_map_region+0x2cd/0x4f0 [dfl_afu]
[ 106.875839] afu_ioctl+0x258/0x380 [dfl_afu]
[ 106.880108] do_vfs_ioctl+0xa9/0x720
[ 106.883688] ksys_ioctl+0x60/0x90
[ 106.887007] __x64_sys_ioctl+0x16/0x20
With the previous value of 2, afu_dma_map_region was being omitted. I
suspect that the code paths have simply changed since the value of 2 was
chosen a decade ago, but it's also possible that it varies based on which
mapping function was used, compiler inlining choices, etc. In any case,
it's best to err on the side of skipping less.
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
It's used by probe and that isn't an init function. Drop this so that we
don't get a section mismatch.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: David Müller <dave.mueller@gmx.ch>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: 7c2e07130090 ("clk: x86: Add system specific quirk to mark clocks as critical")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The nvme target hadn't been taking the Get Log Page offset parameter
into consideration, and so has been returning corrupted log pages when
offsets are used. Since many tools, including nvme-cli, split the log
request to 4k, we've been breaking discovery log responses when more
than 3 subsystems exist.
Fix the returned data by internally generating the entire discovery
log page and copying only the requested bytes into the user buffer. The
command log page offset type has been modified to a native __le64 to
make it easier to extract the value from a command.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Minwoo Im <minwoo.im@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch fixes a long-standing bug that initialized the FC-NVME
cmnd iu CSN value to 1. Early FC-NVME specs had the connection starting
with CSN=1. By the time the spec reached approval, the language had
changed to state a connection should start with CSN=0. This patch
corrects the initialization value for FC-NVME connections.
Additionally, in reviewing the transport, the CSN value is assigned to
the new IU early in the start routine. It's possible that a later dma
map request may fail, causing the command to never be sent to the
controller. Change the location of the assignment so that it is
immediately prior to calling the lldd. Add a comment block to explain
the impacts if the lldd were to additionally fail sending the command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
commit 5b0d62108b46 ("mmc: sdhci-omap: Add platform specific reset
callback") skips data resets during tuning operation. Because of this,
a data error or data finish interrupt might still arrive after a command
error has been handled and the mrq ended. This ends up with a "mmc0: Got
data interrupt 0x00000002 even though no data operation was in progress"
error message.
Fix this by adding a platform specific callback for sdhci_irq. Mark the
mrq as a failure but wait for a data interrupt instead of calling
finish_mrq().
Fixes: 5b0d62108b46 ("mmc: sdhci-omap: Add platform specific reset
callback")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case the IOMMU API is not available compiling host1x fails with
the following error:
In file included from drivers/gpu/host1x/hw/host1x06.c:27:
drivers/gpu/host1x/hw/channel_hw.c: In function ‘host1x_channel_set_streamid’:
drivers/gpu/host1x/hw/channel_hw.c:118:30: error: implicit declaration of function
‘dev_iommu_fwspec_get’; did you mean ‘iommu_fwspec_free’? [-Werror=implicit-function-declaration]
struct iommu_fwspec *spec = dev_iommu_fwspec_get(channel->dev->parent);
^~~~~~~~~~~~~~~~~~~~
iommu_fwspec_free
Fixes: de5469c21ff9 ("gpu: host1x: Program the channel stream ID")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
When fb is tiled and fb->height isn't the multiple of tile's height,
the format fb->size = fb->stride * fb->height, will get a smaller size
than the actual size. As the memory height of tiled fb should be multiple
of tile's height.
Fixes: 7f1a93b1f1d1 ("drm/i915/gvt: Correct the calculation of plane size")
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Since commit 648e921888ad ("clk: x86: Stop marking clocks as
CLK_IS_CRITICAL"), the pmc_plt_clocks of the Bay Trail SoC are
unconditionally gated off. Unfortunately this will break systems where these
clocks are used for external purposes beyond the kernel's knowledge. Fix it
by implementing a system specific quirk to mark the necessary pmc_plt_clks as
critical.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Signed-off-by: David Müller <dave.mueller@gmx.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
When bio_add_pc_page() fails in bio_copy_user_iov() we should free
the page we just allocated otherwise we are leaking it.
Cc: linux-block@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
During a safe hot remove, the OS powers off the slot, which may cause a
Data Link Layer State Changed event. The slot has already been set to
OFF_STATE, so that event results in re-enabling the device, making it
impossible to safely remove it.
Clear out the Presence Detect Changed and Data Link Layer State Changed
events when the disabled slot has settled down.
It is still possible to re-enable the device if it remains in the slot
after pressing the Attention Button by pressing it again.
Fixes the problem that Micah reported below: an NVMe drive power button may
not actually turn off the drive.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203237
Reported-by: Micah Parrish <micah.parrish@hpe.com>
Tested-by: Micah Parrish <micah.parrish@hpe.com>
Signed-off-by: Sergey Miroshnichenko <s.miroshnichenko@yadro.com>
[bhelgaas: changelog, add bugzilla URL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.19+
|
|
Now that we allow drivers to always need to set larger than required
DMA masks we need to be a little more careful in the sun4v PCI iommu
driver to chose when to select the ATU support - a larger DMA mask
can be set even when the platform does not support ATU, so we always
have to check if it is avaiable before using it. Add a little helper
for that and use it in all the places where we make ATU usage decisions
based on the DMA mask.
Fixes: 24132a419c68 ("sparc64/pci_sun4v: allow large DMA masks")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Meelis Roos <mroos@linux.ee>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
The introduction of multipage bio vectors broke pblk's partial read
logic due to it not being prepared for multipage bio vectors.
Use bio vector iterators instead of direct bio vector indexing.
Fixes: 07173c3ec276 ("block: enable multipage bvecs")
Reported-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Updated description.
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When a QP is put into error state, the send queue will be flushed.
This mechanism is implemented in both the first and the second leg
of the send engine. Since the second leg is only responsible for
data transactions in the KDETH space for the TID RDMA WRITE request,
it should not perform the flushing of the send queue.
This patch removes the flushing function of the second leg, but
still keeps the bailing out of the QP if it is put into error state.
Fixes: 70dcb2e3dc6a ("IB/hfi1: Add the TID second leg send packet builder")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
wcd9335.c: undefined reference to 'devm_regmap_add_irq_chip'
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 7769db588384 ("drm/i915/dp: optimize eDP 1.4+ link config fast
and narrow") started to optize the eDP 1.4+ link config, both per spec
and as preparation for display stream compression support.
Sadly, we again face panels that flat out fail with parameters they
claim to support. Revert, and go back to the drawing board.
v2: Actually revert to max params instead of just wide-and-slow.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109959
Fixes: 7769db588384 ("drm/i915/dp: optimize eDP 1.4+ link config fast and narrow")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.0+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Albert Astals Cid <aacid@kde.org> # v5.0 backport
Tested-by: Emanuele Panigati <ilpanich@gmail.com> # v5.0 backport
Tested-by: Matteo Iervasi <matteoiervasi@gmail.com> # v5.0 backport
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405075220.9815-1-jani.nikula@intel.com
(cherry picked from commit f11cb1c19ad0563b3c1ea5eb16a6bac0e401f428)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Re-enable clock gating of DDI clocks.
v2: Fix the default ddi clk state for mipi-dsi (Imre)
Fixes: 1026bea00381 ("drm/i915/icl: Ungate DSI clocks")
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553513202-13863-2-git-send-email-vandita.kulkarni@intel.com
(cherry picked from commit 942d1cf48eae3fcd7e973cfb708d5c4860f0c713)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
IO enable sequencing needs ddi clocks enabled.
These clocks will be gated at a later point in
the enable sequence.
v2: Fix the commit header (Uma)
v3: Remove the redundant read (Ville)
Fixes: 949fc52af19e ("drm/i915/icl: add pll mapping for DSI")
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553513202-13863-1-git-send-email-vandita.kulkarni@intel.com
(cherry picked from commit c5b81a325263a891d5811aabe938c87e03db4c37)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
nvme_cancel_request() is used in error handler, and it is always
reliable to cancel request synchronously, and avoids possible race
in which request may be completed after real hw queue is destroyed.
One issue is reported by our customer on NVMe RDMA, in which freed ib
queue pair may be used in nvme_rdma_complete_rq().
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: James Smart <james.smart@broadcom.com>
Cc: linux-nvme@lists.infradead.org
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
