| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
At the moment, the WWAN core provides wwan_port_txon/off() to implement
blocking writes. The tx() port operation should not block, instead
wwan_port_txon/off() should be called when the TX queue is full or has
free space again.
However, in some cases it is not straightforward to make use of that
functionality. For example, the RPMSG API used by rpmsg_wwan_ctrl.c
does not provide any way to be notified when the TX queue has space
again. Instead, it only provides the following operations:
- rpmsg_send(): blocking write (wait until there is space)
- rpmsg_trysend(): non-blocking write (return error if no space)
- rpmsg_poll(): set poll flags depending on TX queue state
Generally that's totally sufficient for implementing a char device,
but it does not fit well to the currently provided WWAN port ops.
Most of the time, using the non-blocking rpmsg_trysend() in the
WWAN tx() port operation works just fine. However, with high-frequent
writes to the char device it is possible to trigger a situation
where this causes issues. For example, consider the following
(somewhat unrealistic) example:
# dd if=/dev/zero bs=1000 of=/dev/wwan0qmi0
dd: error writing '/dev/wwan0qmi0': Resource temporarily unavailable
1+0 records out
This fails immediately after writing the first record. It's likely
only a matter of time until this triggers issues for some real application
(e.g. ModemManager sending a lot of large QMI packets).
The rpmsg_char device does not have this problem, because it uses
rpmsg_trysend() and rpmsg_poll() to support non-blocking operations.
Make it possible to use the same in the RPMSG WWAN driver by adding
two new optional wwan_port_ops:
- tx_blocking(): send data blocking if allowed
- tx_poll(): set additional TX poll flags
This integrates nicely with the RPMSG API and does not require
any change in existing WWAN drivers.
With these changes, the dd example above blocks instead of exiting
with an error.
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The remote processor messaging (rpmsg) subsystem provides an interface
to communicate with other remote processors. On many Qualcomm SoCs this
is used to communicate with an integrated modem DSP that implements most
of the modem functionality and provides high-level protocols like
QMI or AT to allow controlling the modem.
For QMI, most older Qualcomm SoCs (e.g. MSM8916/MSM8974) have
a standalone "DATA5_CNTL" channel that allows exchanging QMI messages.
Note that newer SoCs (e.g. SDM845) only allow exchanging QMI messages
via a shared QRTR channel that is available via a socket API on Linux.
For AT, the "DATA4" channel accepts at least a limited set of AT
commands, on many older and newer Qualcomm SoCs, although QMI is
typically the preferred control protocol.
Often there are additional QMI/AT channels (usually named DATA*_CNTL
for QMI and DATA* for AT), but it is not clear if those are really
functional on all devices. Also, at the moment there is no use case
for having multiple QMI/AT ports. If needed more channels could be
added later after more testing.
Note that the data path (network interface) is entirely separate
from the control path and varies between Qualcomm SoCs, e.g. "IPA"
on newer Qualcomm SoCs or "BAM-DMUX" on some older ones.
The RPMSG WWAN CTRL driver exposes the QMI/AT control ports via the
WWAN subsystem, and therefore allows userspace like ModemManager to
set up the modem. Until now, ModemManager had to use the RPMSG-specific
rpmsg-char where the channels must be explicitly exposed as a char
device first and don't show up directly in sysfs.
The driver is a fairly simple glue layer between WWAN and RPMSG
and is mostly based on the existing mhi_wwan_ctrl.c and rpmsg_char.c.
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most device_id structs provide a driver_data field that can be used
by drivers to associate data more easily for a particular device ID.
Add the same for the rpmsg_device_id.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1f3c98eaddec857e16a7a1c6cd83317b3dc89438.
Does not build...
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify the pr_info content from int to char *, this looks more readable.
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
static void ec_bhf_remove(struct pci_dev *dev)
{
...
struct ec_bhf_priv *priv = netdev_priv(net_dev);
unregister_netdev(net_dev);
free_netdev(net_dev);
pci_iounmap(dev, priv->dma_io);
pci_iounmap(dev, priv->io);
...
}
priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls.
Fixes: 6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When memcpy_to_msg() fails in virtio_transport_seqpacket_do_dequeue(),
we already set `dequeued_len` with the negative error value returned
by memcpy_to_msg().
So we can directly check `dequeued_len` value instead of using a
dedicated flag variable to skip the copy path for the rest of
fragments.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vsock_wait_data() is used only by STREAM and SEQPACKET sockets,
so let's rename it to vsock_connectible_wait_data(), using the same
nomenclature (connectible) used in other functions after the
introduction of SEQPACKET.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vsock_has_data() is used only by STREAM and SEQPACKET sockets,
so let's rename it to vsock_connectible_has_data(), using the same
nomenclature (connectible) used in other functions after the
introduction of SEQPACKET.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary label chunk_exit and return directly.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
something fails
If reloading the static config fails for whatever reason, for example if
sja1105_static_config_check_valid() fails, then we "goto out_unlock_ptp"
but we print anyway that "Reset switch and programmed static config.",
which is confusing because we didn't. We also do a bunch of other stuff
like reprogram the XPCS and reload the credit-based shapers, as if a
switch reset took place, which didn't.
So just unlock the PTP lock and goto out, skipping all of that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for SJA1110
Currently sja1105_static_config_check_valid() is coded up to detect
whether TTEthernet is supported based on device ID, and this check was
not updated to cover SJA1110.
However, it is desirable to have as few checks for the device ID as
possible, so the driver core is more generic. So what we can do is look
at the static config table operations implemented by that specific
switch family (populated by sja1105_static_config_init) whether the
schedule table has a non-zero maximum entry count (meaning that it is
supported) or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current rx page reuse handling process, the rx page buffer may
have conflict between driver and stack in high-pressure scenario.
To fix this problem, we need to check whether the page is only owned
by driver at the begin and at the end of a page to make sure there is
no reuse conflict between driver and stack when desc_cb->page_offset
is rollbacked to zero or increased.
Fixes: fa7711b888f2 ("net: hns3: optimize the rx page reuse handling process")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that powering down the BASE_TIMER_CLK does not turn off the
microcontroller, just its timers, including the one for the watchdog.
So the embedded microcontroller is still running, and potentially still
doing things.
To prevent unwanted interference, we should power down the BASE_MCSS_CLK
as well (MCSS = microcontroller subsystem).
The trouble is that currently we turn off the BASE_TIMER_CLK for SJA1110
from the .clocking_setup() method, mostly because this is a Clock
Generation Unit (CGU) setting which was traditionally configured in that
method for SJA1105. But in SJA1105, the CGU was used for bringing up the
port clocks at the proper speeds, and in SJA1110 it's not (but rather
for initial configuration), so it's best that we rebrand the
sja1110_clocking_setup() method into what it really is - an implementation
of the .disable_microcontroller() method.
Since disabling the microcontroller only needs to be done once, at probe
time, we can choose the best place to do that as being in sja1105_setup(),
before we upload the static config to the device. This guarantees that
the static config being used by the switch afterwards is really ours.
Note that the procedure to upload a static config necessarily resets the
switch. This already did not reset the microcontroller, only the switch
core, so since the .disable_microcontroller() method is guaranteed to be
called by that point, if it's disabled, it remains disabled. Add a
comment to make that clear.
With the code movement for SJA1110 from .clocking_setup() to
.disable_microcontroller(), both methods are optional and are guarded by
"if" conditions.
Tested by enabling in the device tree the rev-mii switch port 0 that
goes towards the microcontroller, and flashing a firmware that would
have networking. Without this patch, the microcontroller can be pinged,
with this patch it cannot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
