Merge tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull mtd updates from Miquel Raynal:
 "MTD changes:

   - Apart from a binding conversion to yaml, only minor changes/small
     fixes have been merged.

  Raw NAND changes:

   - Minor fixes for various controller drivers like DMA mapping checks,
     better timing derivations or bitflip statistics.

   - some Hynix NAND flashes were not supporting read-retries, so don't
     even try to do it

  SPI NAND changes:

   - In order to support high-speed modes, certain chips need extra
     configuration like adding more dummy cycles. This is now possible,
     especially on Winbond chips.

   - Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).

  SPI NOR changes:

   - A notable changes is the fix for exiting 4-byte addressing on
     Infineon SEMPER flashes. These flashes do not support the standard
     EX4B opcode (E9h), and use a vendor-specific opcode (B8h) instead.

   - There is also a fix for unlocking flashes that are write-protected
     at power-on. This was caused by using an uninitialized mtd_info in
     spi_nor_try_unlock_all()"

* tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (26 commits)
  mtd: spinand: winbond: Add comment about the maximum frequency
  mtd: spinand: winbond: Enable high-speed modes on w35n0xjw
  mtd: spinand: winbond: Enable high-speed modes on w25n0xjw
  mtd: spinand: Add a ->configure_chip() hook
  mtd: spinand: Add a frequency field to all READ_FROM_CACHE variants
  mtd: spinand: Fix macro alignment
  spi: spi-mem: Take into account the actual maximum frequency
  spi: spi-mem: Use picoseconds for calculating the op durations
  mtd: rawnand: atmel: set pmecc data setup time
  mtd: spinand: propagate spinand_wait() errors from spinand_write_page()
  mtd: rawnand: fsmc: Add missing check after DMA map
  mtd: rawnand: rockchip: Add missing check after DMA map
  mtd: rawnand: hynix: don't try read-retry on SLC NANDs
  mtd: rawnand: atmel: Fix dma_mapping_error() address
  mtd: nand: brcmnand: fix mtd corrected bits stat
  mtd: rawnand: renesas: Add missing check after DMA map
  mtd: spinand: gigadevice: Add support for GD5F1GM9 chips
  mtd: nand: brcmnand: replace manual string choices with standard helpers
  mtd: map: Don't use "proxy" headers
  mtd: spi-nor: Fix spi_nor_try_unlock_all()
  ...

3 files changed, 75 insertions, 59 deletions

diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
index 335f8204aa1e..587af4968255 100644
--- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
@@ -20,7 +20,7 @@ properties:
           - pattern: "^((((micron|spansion|st),)?\
               (m25p(40|80|16|32|64|128)|\
               n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
-              atmel,at25df(321a|641|081a)|\
+              atmel,at(25|26)df(321a|641|081a)|\
               everspin,mr25h(10|40|128|256)|\
               (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
               (mxicy|macronix),mx25u(4033|4035)|\
diff --git a/Documentation/devicetree/bindings/mtd/nxp,lpc1773-spifi.yaml b/Documentation/devicetree/bindings/mtd/nxp,lpc1773-spifi.yaml
new file mode 100644
index 000000000000..d6efb9417b7a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/nxp,lpc1773-spifi.yaml
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/nxp,lpc1773-spifi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP SPI Flash Interface (SPIFI)
+
+description:
+  NXP SPIFI is a specialized SPI interface for serial Flash devices.
+  It supports one Flash device with 1-, 2- and 4-bits width in SPI
+  mode 0 or 3. The controller operates in either command or memory
+  mode. In memory mode the Flash is accessible from the CPU as
+  normal memory.
+
+maintainers:
+  - Frank Li <Frank.Li@nxp.com>
+
+properties:
+  compatible:
+    const: nxp,lpc1773-spifi
+
+  reg:
+    maxItems: 2
+
+  reg-names:
+    items:
+      - const: spifi
+      - const: flash
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: spifi
+      - const: reg
+
+  resets:
+    maxItems: 1
+
+  spi-cpol:
+    enum: [0, 3]
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - clocks
+  - clock-names
+
+allOf:
+  - $ref: /schemas/spi/spi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/lpc18xx-ccu.h>
+
+    spi@40003000 {
+        compatible = "nxp,lpc1773-spifi";
+        reg = <0x40003000 0x1000>, <0x14000000 0x4000000>;
+        reg-names = "spifi", "flash";
+        interrupts = <30>;
+        clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>;
+        clock-names = "spifi", "reg";
+        resets = <&rgu 53>;
+    };
+
diff --git a/Documentation/devicetree/bindings/mtd/nxp-spifi.txt b/Documentation/devicetree/bindings/mtd/nxp-spifi.txt
deleted file mode 100644
index f8b6b250654e..000000000000
--- a/Documentation/devicetree/bindings/mtd/nxp-spifi.txt
+++ /dev/null
@@ -1,58 +0,0 @@
-* NXP SPI Flash Interface (SPIFI)
-
-NXP SPIFI is a specialized SPI interface for serial Flash devices.
-It supports one Flash device with 1-, 2- and 4-bits width in SPI
-mode 0 or 3. The controller operates in either command or memory
-mode. In memory mode the Flash is accessible from the CPU as
-normal memory.
-
-Required properties:
-  - compatible : Should be "nxp,lpc1773-spifi"
-  - reg : the first contains the register location and length,
-          the second contains the memory mapping address and length
-  - reg-names: Should contain the reg names "spifi" and "flash"
-  - interrupts : Should contain the interrupt for the device
-  - clocks : The clocks needed by the SPIFI controller
-  - clock-names : Should contain the clock names "spifi" and "reg"
-
-Optional properties:
- - resets : phandle + reset specifier
-
-The SPI Flash must be a child of the SPIFI node and must have a
-compatible property as specified in bindings/mtd/jedec,spi-nor.txt
-
-Optionally it can also contain the following properties.
- - spi-cpol : Controller only supports mode 0 and 3 so either
-              both spi-cpol and spi-cpha should be present or
-              none of them
- - spi-cpha : See above
- - spi-rx-bus-width : Used to select how many pins that are used
-                      for input on the controller
-
-See bindings/spi/spi-bus.txt for more information.
-
-Example:
-spifi: spifi@40003000 {
-	compatible = "nxp,lpc1773-spifi";
-	reg = <0x40003000 0x1000>, <0x14000000 0x4000000>;
-	reg-names = "spifi", "flash";
-	interrupts = <30>;
-	clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>;
-	clock-names = "spifi", "reg";
-	resets = <&rgu 53>;
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		spi-cpol;
-		spi-cpha;
-		spi-rx-bus-width = <4>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			label = "data";
-			reg = <0 0x200000>;
-		};
-	};
-};
-