ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.

There's no change to dtbs_install as the flat structure is maintained on
install.

The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
  been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
  company (e.g. gemini, nspire)

The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>

1 files changed, 631 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
new file mode 100644
index 000000000000..830b5a5064f2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
@@ -0,0 +1,631 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+#include "imx6ull-dhcor-som.dtsi"
+
+/ {
+	aliases {
+		/delete-property/ spi2;
+		/delete-property/ spi3;
+		i2c0 = &i2c2;
+		i2c1 = &i2c1;
+		mmc2 = &usdhc2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+		serial0 = &uart1;
+		serial1 = &uart6; /* DHCOM UART2, special hardware required */
+		serial2 = &uart3;
+		serial3 = &uart2; /* Use BT UART always as ttymxc3 */
+		serial4 = &uart4;
+		serial5 = &uart5;
+		spi0 = &ecspi1;
+		spi1 = &ecspi4; /* DHCOM SPI2, special hardware required */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_ext_3v3_ref: regulator-ext-3v3-ref {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_3V3_REF";
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg1-vbus";
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 5 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg2-vbus";
+	};
+
+	/* SoM with WiFi/BT: WiFi pin WL_REG_ON is connected to a DHCOM GPIO */
+	/omit-if-no-ref/ usdhc1_pwrseq: usdhc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; /* GPIO H */
+	};
+};
+
+/* SoM with WiFi/BT: BT pin BT_REG_ON is connected to a DHCOM GPIO */
+&bluetooth {
+	shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+};
+
+&can1 {
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
+ * Only if this pins are used as CAN interface enable it on board layer.
+ */
+&can2 {
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM SPI1 */
+&ecspi1 {
+	cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * DHCOM SPI2
+ * Special hardware required that uses the pins of FEC2. Therefore this SPI
+ * interface can only be used if FEC2 is disabled.
+ */
+&ecspi4 {
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM ETH1 */
+&fec1 {
+	phy-handle = <&mdio2_phy0>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&pinctrl_fec1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* DHCOM ETH2 */
+&fec2 {
+	phy-handle = <&mdio2_phy1>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&pinctrl_fec2>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio2_phy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			clock-names = "rmii-ref";
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
+			pinctrl-names = "default";
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+
+		mdio2_phy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			clock-names = "rmii-ref";
+			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_fec2_phy &pinctrl_snvs_fec2_phy>;
+			pinctrl-names = "default";
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "DHCOM-INT",
+		"", "", "", "",
+		"", "", "DHCOM-I", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+	pinctrl-0 = <&pinctrl_spi1_switch
+		     &pinctrl_dhcom_i &pinctrl_dhcom_int>;
+	pinctrl-names = "default";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "DHCOM-L", "DHCOM-K", "DHCOM-M",
+		"DHCOM-J", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+		"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+		"DHCOM-N", "", "", "";
+	pinctrl-0 = <&pinctrl_dhcom_j &pinctrl_dhcom_k
+		     &pinctrl_dhcom_l &pinctrl_dhcom_m
+		     &pinctrl_dhcom_n &pinctrl_dhcom_o
+		     &pinctrl_dhcom_p &pinctrl_dhcom_q
+		     &pinctrl_dhcom_r &pinctrl_dhcom_s
+		     &pinctrl_dhcom_t &pinctrl_dhcom_u>;
+	pinctrl-names = "default";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"DHCOM-A", "DHCOM-B", "DHCOM-C", "DHCOM-D",
+		"DHCOM-E", "", "", "DHCOM-F",
+		"DHCOM-G", "DHCOM-H", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+	pinctrl-0 = <&pinctrl_snvs_dhcom_a &pinctrl_snvs_dhcom_b
+		     &pinctrl_snvs_dhcom_c &pinctrl_snvs_dhcom_d
+		     &pinctrl_snvs_dhcom_e &pinctrl_snvs_dhcom_f
+		     &pinctrl_snvs_dhcom_g &pinctrl_snvs_dhcom_h>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM I2C2 */
+&i2c1 {
+	rtc_i2c: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	/* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH1 */
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	/* TI ADC101C027 */
+	adc@51 {
+		compatible = "ti,adc101c";
+		reg = <0x51>;
+		vref-supply = <&reg_ext_3v3_ref>;
+	};
+
+	/* TI ADC101C027 */
+	adc@52 {
+		compatible = "ti,adc101c";
+		reg = <0x52>;
+		vref-supply = <&reg_ext_3v3_ref>;
+	};
+
+	/* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH2 */
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+/* DHCOM I2C1 */
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-0 = <&pinctrl_lcdif>;
+	pinctrl-names = "default";
+};
+
+&pwm1 {
+	pinctrl-0 = <&pinctrl_pwm1>;
+	pinctrl-names = "default";
+};
+
+&sai2 {
+	assigned-clock-rates = <320000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>;
+	pinctrl-0 = <&pinctrl_sai2>;
+	pinctrl-names = "default";
+};
+
+&tsc {
+	measure-delay-time = <0xffff>;
+	pinctrl-0 = <&pinctrl_tsc>;
+	pinctrl-names = "default";
+	pre-charge-time = <0xfff>;
+	touchscreen-average-samples = <32>;
+	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+};
+
+/* DHCOM UART1 */
+&uart1 {
+	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * DHCOM UART2 (alternative)
+ * Special hardware required that uses DHCOM GPIO pins for DHCOM UART2.
+ * Therefore this UART interface can only be used if DHCOM GPIOs J/K/L/M are
+ * removed from GPIO hog muxing.
+ */
+&uart6 {
+	pinctrl-0 = <&pinctrl_uart6>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&usbotg1 {
+	adp-disable;
+	disable-over-current;
+	dr_mode = "otg";
+	hnp-disable;
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	pinctrl-names = "default";
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current; /* Overcurrent pin is used for TSC */
+	dr_mode = "host";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	pinctrl-names = "default";
+	tpl-support;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+/* WiFi on LGA */
+&usdhc1 {
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+};
+
+/* eMMC on module */
+&usdhc2 {
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&iomuxc {
+	/* DHCOM GPIOs I..U + INT_HIGHEST_PRIORITY */
+	pinctrl_dhcom_i: dhcom-i-grp {
+		fsl,pins = <MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x400120b0>;
+	};
+
+	pinctrl_dhcom_j: dhcom-j-grp {
+		fsl,pins = <MX6UL_PAD_CSI_HSYNC__GPIO4_IO20	0x400120b0>;
+	};
+
+	pinctrl_dhcom_k: dhcom-k-grp {
+		fsl,pins = <MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x400120b0>;
+	};
+
+	pinctrl_dhcom_l: dhcom-l-grp {
+		fsl,pins = <MX6UL_PAD_CSI_MCLK__GPIO4_IO17	0x400120b0>;
+	};
+
+	pinctrl_dhcom_m: dhcom-m-grp {
+		fsl,pins = <MX6UL_PAD_CSI_VSYNC__GPIO4_IO19	0x400120b0>;
+	};
+
+	pinctrl_dhcom_n: dhcom-n-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x400120b0>;
+	};
+
+	pinctrl_dhcom_o: dhcom-o-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x400120b0>;
+	};
+
+	pinctrl_dhcom_p: dhcom-p-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x400120b0>;
+	};
+
+	pinctrl_dhcom_q: dhcom-q-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x400120b0>;
+	};
+
+	pinctrl_dhcom_r: dhcom-r-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x400120b0>;
+	};
+
+	pinctrl_dhcom_s: dhcom-s-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x400120b0>;
+	};
+
+	pinctrl_dhcom_t: dhcom-t-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x400120b0>;
+	};
+
+	pinctrl_dhcom_u: dhcom-u-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x400120b0>;
+	};
+
+	pinctrl_dhcom_int: dhcom-int-grp {
+		fsl,pins = <MX6UL_PAD_JTAG_TMS__GPIO1_IO11	0x400120b0>;
+	};
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x100b1
+			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x1b0b0 /* SS0 */
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO	0x100b1
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI	0x100b1
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK	0x100b1
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b0b0 /* SS0 */
+		>;
+	};
+
+	pinctrl_fec1: fec1-grp {
+		fsl,pins = <
+			/* FEC1 uses MDIO bus from FEC2 */
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b010
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b010
+		>;
+	};
+
+	pinctrl_fec1_phy: fec1-phy-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0xb0 /* SMSC PHY reset */
+		>;
+	};
+
+	pinctrl_fec2: fec2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b010
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b010
+		>;
+	};
+
+	pinctrl_fec2_phy: fec2-phy-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24	0xb0 /* SMSC PHY reset */
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	0x4001b8b0
+		>;
+	};
+
+	pinctrl_lcdif: lcdif-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
+		>;
+	};
+
+	pinctrl_pwm1: pwm1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__PWM1_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_sai2: sai2-grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
+		>;
+	};
+
+	pinctrl_tsc: tsc-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0xb0
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6: uart6-grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__UART6_DCE_TX	0x1b0b1
+			MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x120b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B	0x17059 /* SD2 Reset */
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	/* DHCOM GPIOs A..H */
+	pinctrl_snvs_dhcom_a: snvs-dhcom-a-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_b: snvs-dhcom-b-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_c: snvs-dhcom-c-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_d: snvs-dhcom-d-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_e: snvs-dhcom-e-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_f: snvs-dhcom-f-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_g: snvs-dhcom-g-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_h: snvs-dhcom-h-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400120b0>;
+	};
+
+	pinctrl_snvs_fec1_phy: snvs-fec1-phy-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0xb1 /* SMSC PHY Int */
+		>;
+	};
+
+	pinctrl_snvs_fec2_phy: snvs-fec2-phy-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0xb1 /* SMSC PHY Int */
+		>;
+	};
+};