| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Until commit 919d6924ae9b ("clk: bcm: rpi: Turn firmware clock on/off
when preparing/unpreparing") the clk-raspberrypi driver wasn't able
to change the state of the V3D clock. Only the clk-bcm2835 was able
to do this before. After this commit both drivers were able to work
against each other, which could result in a system freeze. One step
to avoid this conflict is to switch all V3D consumer to the firmware
clock.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/linux-arm-kernel/727aa0c8-2981-4662-adf3-69cac2da956d@samsung.com/
Fixes: 919d6924ae9b ("clk: bcm: rpi: Turn firmware clock on/off when preparing/unpreparing")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Co-developed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20251005113816.6721-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
|
|
Pull SoC dt updates from Arnd Bergmann:
"There are five sets of new SoCs that get added in existing families,
all of them being either upgrades or cut-down versions of the older
chips:
- Apple M2 Pro, M2 Max and M2 Ultra, used in the 2022/2023 generation
of high-end workstations and laptops from Apple. Linux has been
working on these for a while but stil requires patches.
- Axis Artpec8 is an Armv8 chip based on Samsung Exynos design,
unlike the earlier Armv7 Artpec6 from the same company that was
part of a separate family of chips.
- NXP i.MX91 is a cut-down version of i.MX93, using only a single
Cortex-A55 core.
- Qualcomm Lemans Auto is a variant of the Lemans SoC that was
originally merged under the sa8775p name, the differences being
mostly the firmware configuration of the platform.
- Four new Renesas SoCs RZ/T2H (r9a09g077m44), RZ/N2H (r9a09g087m44),
RZ/T2H (r9a09g077), and RZ/N2H (r9a09g087) are all industrial
bedded SoCs based on Cortex-A55 cores
In total, there are 65 new machines, including:
- Industrial embedded system and single-board computers based on NXP,
Allwinner, TI, Rockchips, Marvell, Xilinx Spacemit, Starfive chips.
- Reference boards for the newly added Renesas, Qualcomm, NXP and
Axis ARMv8 chips as well as Microchip's MPFS RISC-V SoC
- Laptops and Workstations using Apple M2 and Qualcomm Snapdragon X1
chips.
- Several Samsung phones using Qualcomm Snapdragon chips
- Set-top boxes based on Allwinner H313
- Five BMC boards using 32-bit ASpeed SoCs
- Three network routers using IXP4xx (ARMv5!) and Broadcom bcm4708
(ARMv7) SoCs
Two machines get phased out because they were available only in small
quantities but never made it into products: one STi407 based reference
board, and a Snapdragon 845 based Chromebook.
Aside from the newly added machines, a lot of work went into improving
hardware support on the existing machines and cleaning up contents for
validation"
* tag 'soc-dt-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (931 commits)
arm64: dts: apm-shadowcat: Drop "apm,xgene2-pcie" compatible
arm64: dts: apm-shadowcat: Move slimpro nodes out of "simple-bus" node
ARM: dts: microchip: sam9x7: Add qspi controller
arm64: dts: qcom: Add MST pixel streams for displayport
arm64: dts: qcom: sm6350: correct DP compatibility strings
arm64: dts: qcom: monaco-evk: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300-ride: Enable Adreno 623 GPU
arm64: dts: qcom: qcs8300: Add gpu and gmu nodes
arm64: dts: allwinner: h313: Add Amediatech X96Q
dt-bindings: arm: sunxi: Add Amediatech X96Q
arm64: dts: apple: t8015: Add SPMI node
arm64: dts: apple: t8012: Add SPMI node
arm64: dts: apple: Add J180d (Mac Pro, M2 Ultra, 2023) device tree
arm64: dts: rockchip: Add devicetree for the ROC-RK3588-RT
dt-bindings: arm: rockchip: Add Firefly ROC-RK3588-RT
arm64: dts: rockchip: update pinctrl names for Radxa E52C
arm64: dts: rockchip: remove vcc_3v3_pmu regulator for Radxa E52C
arm64: dts: apple: Add J474s, J475c and J475d device trees
arm64: dts: apple: Add J414 and J416 Macbook Pro device trees
arm64: dts: apple: Add initial t6020/t6021/t6022 DTs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 device tree updates for v6.18
This update includes:
- sama7d65 and curiosity board: addition of gpio, leds and usart3
- sam9x75: qspi node
- one cleanup
* tag 'at91-dt-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: microchip: sam9x7: Add qspi controller
ARM: dts: microchip: sama7d65: add uart3 definition for flexcom3 peripheral
ARM: dts: microchip: sama7d65: Add GPIO buttons and LEDs
ARM: dts: microchip: Minor whitespace cleanup
Link: https://lore.kernel.org/r/20250922170346.40876-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap into soc/dt
ARM: dts: ti: omap updates for v6.18
These are all minor corrections to the dts files.
* tag 'omap-for-v6.18/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap:
ARM: dts: omap: am335x-cm-t335: Remove unused mcasp num-serializer property
ARM: dts: ti: omap: omap3-devkit8000-lcd: Fix ti,keep-vref-on property to use correct boolean syntax in DTS
ARM: dts: ti: omap: am335x-baltos: Fix ti,en-ck32k-xtal property in DTS to use correct boolean syntax
ARM: dts: omap: Minor whitespace cleanup
ARM: dts: omap: dm816x: Split 'reg' per entry
ARM: dts: omap: dm814x: Split 'reg' per entry
ARM: dts: am33xx-l4: fix UART compatible
ARM: dts: ti: omap4: Use generic "ethernet" as node name
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner fixes for 6.17
Two device tree style cleanups from the device tree maintainers.
* tag 'sunxi-fixes-for-6.17' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
riscv: dts: allwinner: rename devterm i2c-gpio node to comply with binding
ARM: dts: allwinner: Minor whitespace cleanup
Link: https://lore.kernel.org/r/aMrsUfkTWx8g3bJ7@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
Another missing supply and a wrong headphone gpio level.
* tag 'v6.17-rockchip-dtsfixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix the headphone detection on the orangepi 5
arm64: dts: rockchip: Add vcc supply for SPI Flash on NanoPC-T6
arm64: dts: rockchip: fix second M.2 slot on ROCK 5T
arm64: dts: rockchip: fix USB on RADXA ROCK 5T
arm64: dts: rockchip: Add vcc-supply to SPI flash on Pinephone Pro
arm64: dts: rockchip: fix es8388 address on rk3588s-roc-pc
arm64: dts: rockchip: Fix Bluetooth interrupts flag on Neardi LBA3368
arm64: dts: rockchip: correct network description on Sige5
arm64: dts: rockchip: Minor whitespace cleanup
ARM: dts: rockchip: Minor whitespace cleanup
arm64: dts: rockchip: Add supplies for eMMC on rk3588-orangepi-5
arm64: dts: rockchip: Fix the headphone detection on the orangepi 5 plus
arm64: dts: rockchip: Add vcc-supply to SPI flash on rk3399-pinebook-pro
arm64: dts: rockchip: mark eeprom as read-only for Radxa E52C
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
Allwinner Device Tree changes for 6.18
This tag contains two DT binding header changes that are shared with
the clk tree.
In this cycle we gained support for the MCU PRCM clock and reset
controller on the A523/A527/T527 family of SoCs, the NPU which is a
Vivante GC9000 IP block, and the NPU clock that was missing. The other
PRCM clock controller gained default bus clock rate settings. These
were not configured in the upstream U-boot bootloader, leading to them
running at slower rates. The assigned rates are from the user manual.
There is also a new board, the NetCube Systems Nagami SoM and two of
its carrier boards.
The A523 family development boards now have their internal RTC clocks
configured correctly, so that the RTC does not drift wildly. The missing
functions for the AXP717 on these boards are added. Missing reset GPIOs
and delays for Ethernet PHYs are added. Last, the Cubie A5E now has its
LEDs described and usable.
An overlay for the Orange Pi Zero interface (addon) board was added.
This can be used with the Orange Pi Zero and Zero Plus 2. Default audio
routing for these two boards (to be used with the addon) were added to
complement the overlay.
* tag 'sunxi-dt-for-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: sun55i: Complete AXP717A sub-functions
arm64: dts: allwinner: t527: orangepi-4a: hook up external 32k crystal
arm64: dts: allwinner: t527: avaota-a1: hook up external 32k crystal
arm64: dts: allwinner: a527: cubie-a5e: Drop external 32.768 KHz crystal
arm64: dts: sun55i: a523: Assign standard clock rates to PRCM bus clocks
ARM: dts: sunxi: add support for NetCube Systems Nagami Keypad Carrier
ARM: dts: sunxi: add support for NetCube Systems Nagami Basic Carrier
ARM: dts: sunxi: add support for NetCube Systems Nagami SoM
riscv: dts: allwinner: d1s-t113: Add pinctrl's required by NetCube Systems Nagami SoM
dt-bindings: arm: sunxi: Add NetCube Systems Nagami SoM and carrier board bindings
ARM: dts: allwinner: Add Orange Pi Zero Interface Board overlay
ARM: dts: allwinner: orangepi-zero-plus2: Add default audio routing
ARM: dts: allwinner: orangepi-zero: Add default audio routing
arm64: dts: allwinner: a523: Add NPU device node
arm64: dts: allwinner: a523: Add MCU PRCM CCU node
dt-bindings: clock: sun55i-a523-ccu: Add A523 MCU CCU clock controller
dt-bindings: clock: sun55i-a523-ccu: Add missing NPU module clock
arm64: dts: allwinner: t527: avaota-a1: Add ethernet PHY reset setting
arm64: dts: allwinner: a527: cubie-a5e: Add ethernet PHY reset setting
arm64: dts: allwinner: a527: cubie-a5e: Add LEDs
Link: https://lore.kernel.org/r/aMrtuZg8HlR--TAt@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add support for QSPI controller.
Signed-off-by: Dharma Balasubiramani <dharma.b@microchip.com>
Link: https://lore.kernel.org/r/20250915-sam9x7-qspi-dtsi-v1-1-1cc9adba7573@microchip.com
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.18, round 1
Highlights:
----------
- MPU:
- STM32MP13:
- Add missing Ethernet1/2 PTP reference clocks.
- Add Hardware debug port (HDP).
- STMP32MP15:
- Add resets property to m_can nodes.
- Add Hardware debug port (HDP) and enable it on stm32mp157c-dk2
board.
- Reserve leds for CM4 on stm32mp15xx-ed1 and stm32mp15xx-dkx.
- stm32mp151c-plyaqm:
Use correct dai-format property.
- STM32MP23:
- Add Ethernet1 MAC controller on stm32mp235f-dk board:
It is connected to a RTL8211F-CG phy through RGMII.
- Fix GPIO bank definition & memory size (DDR).
- STM32MP25:
- Add Ethernet1 MAC controller on stm32mp257f-dk board.
It is connected to a RTL8211F-CG phy through RGMII.
- Add Ethernet1 MAC controller on stm32mp257f-ev1 board.
It is connected to a RTL8211F-CG phy through RGMII.
- Add display support by enabling the following IPs on
stm32mp257f-ev1:
* LTDC
* LVDS
* WSVGA LVDS panel (1024x600)
* Panel LVDS backlight as GPIO backlight
* ILI2511 i2c touchscreen
- Add PCIe Root complex and Endpoint support on stm32mp257f-ev1.
Root complex mode is used by default.
* tag 'stm32-dt-for-v6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (30 commits)
arm64: dts: st: fix memory region size on stm32mp235f-dk
arm64: dts: st: remove gpioj and gpiok banks from stm32mp231
arm64: dts: st: enable ethernet1 controller on stm32mp235f-dk
arm64: dts: st: enable ethernet1 controller on stm32mp257f-ev1
arm64: dts: st: enable ethernet1 controller on stm32mp257f-dk
arm64: dts: st: add eth1 pins for stm32mp2x platforms
ARM: dts: stm32: add missing PTP reference clocks on stm32mp13x SoCs
arm64: dts: st: enable display support on stm32mp257f-ev1 board
arm64: dts: st: add clock-cells to syscfg node on stm32mp251
arm64: dts: st: add lvds support on stm32mp255
arm64: dts: st: add ltdc support on stm32mp255
arm64: dts: st: add ltdc support on stm32mp251
ARM: dts: stm32: add resets property to m_can nodes in the stm32mp153
dt-binding: can: m_can: add optional resets property
arm64: dts: st: Enable PCIe on the stm32mp257f-ev1 board
arm64: dts: st: Add PCIe Endpoint mode on stm32mp251
arm64: dts: st: Add PCIe Root Complex mode on stm32mp251
arm64: dts: st: add PCIe pinctrl entries in stm32mp25-pinctrl.dtsi
arm64: defconfig: Enable STMicroelectronics STM32 DMA3 support
ARM: dts: stm32: add Hardware debug port (HDP) on stm32mp157c-dk2 board
...
Link: https://lore.kernel.org/r/13153fc2-1abe-4d53-807a-5d289981a63d@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ETH1/2 miss their PTP reference clock in the SoC device tree. Add them
as the fallback is not correctly handled for PPS generation and it seems
there's no reason to not add them.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Link: https://lore.kernel.org/r/20250901-relative_flex_pps-v4-3-b874971dfe85@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
On the STM32MP153 the m_cam IP cores (a.k.a. FDCAN) have an external
shared reset in the RCC. Add the reset to both m_can nodes.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20250807-stm32mp15-m_can-add-reset-v2-2-f69ebbfced1f@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
On the stm32mp157fc-dk2 board, we can observe the hdp GPOVAL function on
SoC pin E13 accessible on the pin 5 on the Arduino connector CN13.
Add the relevant configuration but keep it disabled as it's used for
debug only.
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Link: https://lore.kernel.org/r/20250711-hdp-upstream-v7-8-faeecf7aaee1@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Introduce hdp node to output a user defined value on port hdp2.
Add pinctrl nodes to be able to output this signal on one SoC pin.
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250711-hdp-upstream-v7-7-faeecf7aaee1@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
A single graph port node without an address (i.e. "reg") should not have
a unit-address, drop it from the "linux,spdif-dit" port node.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250910233740.777077-2-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree changes for 6.18:
- A series from Alexander Stein to clean up the most of dt-schema warnings
for LS1021A
- A couple of changes from Bence Csókás to replace license text comment
with SPDX identifier for imx6-display5 and imx6-aristainetos2 board
- A couple of vfxxx dt-schema cleanups from Fabio Estevam
- A bunch of changes from Frank Li to clean up dt-schema warnings on
various platforms, VF610, LS1021A, i.MX6, etc.
- Minor whitespace cleanup on i.MX8ULL from Krzysztof Kozlowski
- An imx6ulz-bsh-smm-m2 workaround from Wolfgang Birkner to get resume
via console work
* tag 'imx-dt-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (44 commits)
ARM: dts: imx6sll: Use 'dma-names'
ARM: dts: imx6: change rtc compatible string to st,m41t00 from m41t00
ARM: dts: imx6: remove undefined linux,default-trigger source
ARM: dts: imx6ul-pico: add power-supply for vxt,vl050-8048nt-c01
ARM: dts: imx6ul-14x14-evk: add regulator for ov5640
ARM: dts: imx6: replace isl,isl12022 with isil,isl12022 for RTC
ARM: dts: imx6: replace gpio-key with gpio-keys compatible string
ARM: dts: imx6: rename i2c<n>mux i2c-mux-<n>
ARM: dts: imx6: rename node name flash to eeprom
ARM: dts: imx6: rename node i2c-gpio to i2c.
ARM: dts: imx6: rename touch screen's node name to touchscreen
ARM: dts: imx6: remove redundant pinctrl-names
ARM: dts: imx6qdl-aristainetos2: rename ethernet-phy to ethernet-phy@0
ARM: dts: imx6: add interrupt-cells for dlg,da9063 pmic
ARM: dts: imx6: align rtc chip node name to 'rtc'
ARM: dts: imx6: add key- prefix for gpio-keys
ARM: dts: imx6: add #address-cells for gsc@20
ARM: dts: imx6ul-tx6ul: Switch away from deprecated `phy-reset-gpios`
ARM: dts: mba6ul: Add MicIn routing
ARM: dts: ls1021a-tsn: Remove redundant #address-cells for ethernet-switch@1
...
Link: https://lore.kernel.org/r/20250915132535.253859-2-shawnguo2@yeah.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bmc/linux into soc/dt
Further ASPEED devicetree updates for v6.18
New platforms:
- Meta Clemente
Clemente is a compute-tray platform using an AST2600 SoC
Updated platforms:
- Harma (Meta): Hot-swap controller, power monitoring, GPIO names
There are also some devicetree cleanups from Rob and Krzysztof that touch a
variety of platforms and the DTSIs. These lead to fewer warnings emitted for the
ASPEED devicetrees.
* tag 'aspeed-6.18-devicetree-1' of https://git.kernel.org/pub/scm/linux/kernel/git/bmc/linux:
ARM: dts: aspeed: Drop syscon "reg-io-width" properties
ARM: dts: aspeed: Drop "sdhci" compatibles
ARM: dts: aspeed: Fix/add I2C device vendor prefixes
ARM: dts: aspeed: Minor whitespace cleanup
ARM: dts: aspeed: clemente: add Meta Clemente BMC
ARM: dts: aspeed: Add NCSI3 and NCSI4 pinctrl nodes
dt-bindings: arm: aspeed: add Meta Clemente board
ARM: dts: aspeed: harma: add mp5990
ARM: dts: aspeed: harma: revise gpio name
ARM: dts: aspeed: harma: add power monitor support
Link: https://lore.kernel.org/r/5793039afcedeb28179a3c9909631d8251abc73e.camel@codeconstruct.com.au
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
ARM: tegra: Device tree changes for v6.18-rc1
Add DFLL support on Tegra114, fix some issues on Transformer and P880
devices and add support for the ASUS Eee Pad Slider SL101.
* tag 'tegra-for-6.18-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: add support for ASUS Eee Pad Slider SL101
ARM: tegra: transformer-20: fix audio-codec interrupt
ARM: tegra: transformer-20: add missing magnetometer interrupt
ARM: tegra: Add DFLL clock support for Tegra114
ARM: tegra: p880: set correct touchscreen clipping
Link: https://lore.kernel.org/r/20250914063927.89981-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into soc/dt
STi dt fixes:
- Remove unused stih407-clock.dtsi file
* tag 'sti-dt-for-v6.18-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: sti: remove dangling stih407-clock file
Link: https://lore.kernel.org/r/4a710c05-aeeb-4421-b3a1-5bfb8230d51d@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm32 DeviceTree updates for v6.18
Bring a few updates to the MSM8960 platform and add support for the Sony
Xperia SP.
Touch keys support is added to the Samsung Galaxy Grand 2.
A number of DeviceTree cleanups.
* tag 'qcom-arm32-for-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: Use GIC_SPI for interrupt-map for readability
ARM: dts: qcom: sdx55: Add default GIC address cells
ARM: dts: qcom: ipq8064: Add default GIC address cells
ARM: dts: qcom: apq8064: Add default GIC address cells
ARM: dts: qcom: ipq4019: Add default GIC address cells
ARM: dts: qcom: apq8064-mako: Minor whitespace cleanup
ARM: dts: qcom: msm8226-samsung-ms013g: Add touch keys
ARM: dts: qcom: msm8974-samsung-hlte: Add touchkey support
ARM: dts: qcom: pm8921: add vibrator device node
ARM: dts: qcom: add device tree for Sony Xperia SP
dt-bindings: arm: qcom: add Sony Xperia SP
ARM: dts: qcom: msm8960: disable gsbi1 and gsbi5 nodes in msm8960 dtsi
ARM: dts: qcom: msm8960: add gsbi8 and its serial configuration
ARM: dts: qcom: msm8960: add sdcc3 pinctrl states
Link: https://lore.kernel.org/r/20250911220940.3023575-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/vzapolskiy/linux-lpc32xx into soc/dt
ARM: nxp: lpc: device tree updates for v6.18
This pull request contains device tree changes for ARM NXP LPC32xx and
ARM NXP LPC18xx/LPC43xx for v6.18, please pull the following:
- Frank fixes a multitude of device tree checker warnings reported for
NXP LPC18xx/LPC43xx powered boards,
- Vladimir fixes a number of compile time warnings issued by a dt checker
for NXP LPC32xx powered boards,
- Vladimir replaces Roland as a maintainer of NXP LPC32xx platform
device trees, Roland is inactive for more than 10 years.
* tag 'lpc32xx-dt-for-6.18' of https://github.com/vzapolskiy/linux-lpc32xx:
ARM: dts: lpc32xx: Correct PL080 DMA controller device node name
ARM: dts: lpc32xx: Specify #dma-cells property of PL080 DMA controller
ARM: dts: lpc32xx: Specify a precise version of the SD/MMC controller IP
ARM: dts: lpc32xx: Correct SD/MMC controller device node name
ARM: dts: lpc32xx: Correct motor PWM device tree node name
ARM: dts: lpc32xx: Set motor PWM #pwm-cells property value to 3 cells
dt-bindings: arm: nxp: lpc: Assign myself as maintainer of NXP LPC32xx platforms
ARM: dts: lpc18xx: add missed arm,num-irq-priority-bits
ARM: dts: lpc18xx: add #address-cell and #szie-cell for spi flash controller
ARM: dts: lpc4357-myd-lpc4357: change node name mdio0 to mdio
ARM: dts: lpc: change node name 'button[0-9]' to button-[0-9]'
ARM: dts: lpc4357-myd-lpc4357: add power-supply for innolux,at070tn92
ARM: dts: lpc: add cfg surfix in pinctrl child node
ARM: dts: lpc: add #address-cells and #size-cells for sram node
ARM: dts: lpc18xx: swap clock-names bic and cui
ARM: dts: lpc4350-hitex-eval: change node name flash to flash@0
ARM: dts: lpc18xx: rename node name mmcsd to mmc
ARM: dts: lpc18xx: rename node name flash-controller to spi
Link: https://lore.kernel.org/r/20250911130642.41958-1-vz@mleia.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into soc/dt
This pull request contains Broadcom ARM SoC Device Tree changes for
6.18, please pull the following:
- Taishi-san adds support for the Buffalo WXR-1750DHP using a BCM4708
SoC
* tag 'arm-soc/for-6.18/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Add support for Buffalo WXR-1750DHP
dt-bindings: arm: bcm: Add support for Buffalo WXR-1750DHP
Link: https://lore.kernel.org/r/20250910171910.666401-2-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM changes for v6.18
1. Drop S3C2416 SoC from bindings, because it was removed from kernel
in 2023.
2. Add Ethernet attached via SROM controller (memory bus) on SMDK5250.
This wasn't tested, but code should work just like it is working on
Exynos5410-based boards.
* tag 'samsung-dt-6.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: samsung: smdk5250: add sromc node
ARM: dts: samsung: exynos5250: describe sromc bank memory map
ARM: dts: samsung: exynos5410: use multiple tuples for sromc ranges
dt-bindings: arm: samsung: Drop S3C2416
Link: https://lore.kernel.org/r/20250909184559.105777-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into soc/dt
i2c-gpio-fixes-for-6.18
We have dedictaded bindings for scl/sda nowadays. Switch away from the
deprecated plain 'gpios' property.
* tag 'i2c-gpio-fixes-for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
ARM: dts: stm32: use recent scl/sda gpio bindings
ARM: dts: cirrus: ep7211: use recent scl/sda gpio bindings
Link: https://lore.kernel.org/r/aLlgGdrFEjh26knK@shikoro
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
HDMI-CEC and -audio on RK3288-Miqi
* tag 'v6.18-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add HDMI audio to rk3288-miqi
ARM: dts: rockchip: add CEC pinctrl to rk3288-miqi
Link: https://lore.kernel.org/r/12138356.VV5PYv0bhD@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The NetCube Systems Nagami Keypad Carrier uses the Nagami SoM and contains
a TCA8418 connected to a 4x4 matrix keypad. The I2C2 interface is connected
to said TCA8418 and also a header for an PN532 NFC-Module. It also provides
a pin-header for a bi-color status led. Ethernet with PoE support is
available on a screwterminal after magnetics.
Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Link: https://patch.msgid.link/20250831162536.2380589-6-lukas.schmid@netcube.li
[wens@csie.org: fix indentation for board level compatible fallback,
gpio-line-names and keypad matrix.]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The NetCube Systems Nagami Basic Carrier is a Carrier for the Nagami SoM
It provides an ethernet port for the phy on the SoM and some USB-Ports.
All other interfaces and gpios are available on pinheader, except for the
SD-Interface which is available on a micro-sd slot.
Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Link: https://patch.msgid.link/20250831162536.2380589-5-lukas.schmid@netcube.li
[wens@csie.org: fix indentation for board level compatible string fallback]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
NetCube Systems Nagami SoM is a module based around the Allwinner T113s
SoC. It includes the following features and interfaces:
- 128MB DDR3 included in SoC
- 10/100 Mbps Ethernet using LAN8720A phy
- One USB-OTG interface
- One USB-Host interface
- One I2S interface with in and output support
- Two CAN interfaces
- ESP32 over SDIO
- One SPI interface
- I2C EEPROM for MAC address
- One QWIIC I2C Interface with dedicated interrupt pin shared with EEPROM
- One external I2C interface
- SD interface for external SD-Card
Signed-off-by: Lukas Schmid <lukas.schmid@netcube.li>
Link: https://patch.msgid.link/20250831162536.2380589-4-lukas.schmid@netcube.li
[wens@csie.org: fix up pinctrl names for i2c* and i2s_d*;
fix indentation for gpio-line-names and rmii_pe_pins;
fix "pre-magnetics" typo in comment]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Orange Pi Zero interface board is a (mostly) passive adapter from the
13-pin header of the Orange Pi Zero and Orange Pi Zero Plus2 to standard
connectors (2x USB A, 1x Audio/Video output, 1x built-in microphone, 1x
infrared input). Headphones, microphone, infrared (CIR) input, and USB
have been tested with the Orange Pi Zero.
CVBS output is currently not supported.
https://orangepi.com/index.php?route=product/product&product_id=871
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Link: https://patch.msgid.link/20250911-opz-audio-v3-3-9dfd317a8163@posteo.net
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Orange Pi Zero Plus 2 has the same pinout[1] as the Orange Pi
Zero[2] (with the possible exception of line-out left/right being
swapped), and the Orange Pi Zero Interface Board is sold[3] as
compatible with both of them. We can thus use the same audio routing.
[1]: http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-Zero-Plus-2.html
[2]: https://linux-sunxi.org/Xunlong_Orange_Pi_Zero#Expansion_Port
[3]: https://orangepi.com/index.php?route=product/product&product_id=871
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Link: https://patch.msgid.link/20250911-opz-audio-v3-2-9dfd317a8163@posteo.net
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Line out playback and microphone capture work, after enabling the
corresponding ALSA controls. Tested with the Orange Pi Zero interface
board.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Link: https://patch.msgid.link/20250911-opz-audio-v3-1-9dfd317a8163@posteo.net
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
SoCFPGA DTS fix for v6.17
- Fix midio bus probe and PHY address for cylone5 sodia board
* tag 'socfpga_dts_fix_for_v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: sodia: Fix mdio bus probe and PHY address
Link: https://lore.kernel.org/r/20250907123058.175447-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/fixes
mvebu fixes for 6.17 (part 1)
Fix SATA ports on various boards: Macchiatobin, CN913x-solidrun.
Fix audio on Armada 370 DB and OpenRD.
Disable eMMC high-speed modes on the CN9132 CEX-7 module.
Disable runtime reconfiguration for PCIe lanes on the CN9132 CEX-7 module.
* tag 'mvebu-fixes-6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: cn9132-clearfog: fix multi-lane pci x2 and x4 ports
arm64: dts: marvell: cn9132-clearfog: disable eMMC high-speed modes
arm64: dts: marvell: cn913x-solidrun: fix sata ports status
ARM: dts: kirkwood: Fix sound DAI cells for OpenRD clients
ARM64: dts: mcbin: fix SATA ports on Macchiatobin
ARM: dts: armada-370-db: Fix stereo audio input routing on Armada 370
Link: https://lore.kernel.org/r/87ikhnn1pl.fsf@BLaptop.bootlin.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Following the removal of B2120 board support, the st/stih407-clock.dtsi
file has been left unused. Remove it.
Fixes: dee546e1adef ("ARM: sti: drop B2120 board support")
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
A previous commit changed the '#sound-dai-cells' property for the
kirkwood audio controller from 1 to 0 in the kirkwood.dtsi file,
but did not update the corresponding 'sound-dai' property in the
kirkwood-openrd-client.dts file.
This created a mismatch, causing a dtbs_check validation error where
the dts provides one cell (<&audio0 0>) while the .dtsi expects zero.
Remove the extraneous cell from the 'sound-dai' property to fix the
schema validation warning and align with the updated binding.
Fixes: e662e70fa419 ("arm: dts: kirkwood: fix error in #sound-dai-cells size")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Factor out common part from ASUS Eee Pad Transformer TF101 device tree
into tegra20-asus-transformer-common.dtsi and add device tree fragment for
ASUS Eee Pad Slider SL101.
Tested-by: Winona Schroeer-Smith <wolfizen@wolfizen.net> # ASUS SL101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Correct audio-codec interrupt should be PX3 while PX1 is used for external
microphone detection.
Tested-by: Winona Schroeer-Smith <wolfizen@wolfizen.net> # ASUS SL101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add missing interrupt to magnetometer node.
Tested-by: Winona Schroeer-Smith <wolfizen@wolfizen.net> # ASUS SL101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add DFLL clock node to common Tegra114 device tree along with clocks
property to cpu node.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Existing touchscreen clipping is too small and causes problems with
touchscreen accuracy.
Signed-off-by: Jonas Schwöbel <jonasschwoebel@yahoo.de>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
'dma-name' is not a valid property and causes the following dt-schema
warning:
dma-name: b'rx\x00tx\x00' is not of type 'object', 'integer', 'array', 'boolean', 'null'
Fix it by using 'dma-names' instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
m41t00 compatible is not existing. Change it to st,m41t00 to fix below
CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-ts7970.dtb: /soc/bus@2100000/i2c@21a0000/rtc@68: failed to match any schema with compatible: ['m41t00']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Set gpio/off to none for linux,default-trigger.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-phytec-mira-rdk-nand.dtb: user-leds (gpio-leds): user-led1:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
'gpio' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'netdev', 'none', 'rc-feedback', 'torch', 'usb-gadget', 'usb-host', 'usbport']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add power-supply for vxt,vl050-8048nt-c01 to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dtb: panel (vxt,vl050-8048nt-c01): 'power-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add required power supply for ov5640.
Fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtb: camera@3c (ovti,ov5640): 'AVDD-supply' is a required property
from schema $id: http://devicetree.org/schemas/media/i2c/ovti,ov5640.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The compatible string isl,isl12022 is typo, it should be isil,isl12022.
Fix below CHECK_DTBS warning:
arch/arm/boot/dts/nxp/imx/imx6dl-ts7970.dtb: /soc/bus@2100000/i2c@21a0000/rtc@6f: failed to match any schema with compatible: ['isl,isl12022']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Compatible string 'gpio-key' is not existed. Correct it to 'gpio-keys'.
Fix below CHECK_DTBS warnings
arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-emmc.dtb: /gpio-keys: failed to match any schema with compatible: ['gpio-key']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename i2c<n>mux i2c-mux-<n> to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dtb: i2c2mux (i2c-mux-gpio): $nodename:0: 'i2c2mux' does not match '^(i2c-?)?mux'
from schema $id: http://devicetree.org/schemas/i2c/i2c-mux-gpio.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename node name flash to eeprom to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-b450v3.dtb: flash@0 (atmel,at25): $nodename: 'anyOf' conditional failed, one must be fixed:
'flash@0' does not match '^eeprom@[0-9a-f]{1,2}$'
'flash@0' does not match '^fram@[0-9a-f]{1,2}$'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename node name i2c-gpio to i2c to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0010.dtb: / (karo,imx6ul-tx6ul): i2c-gpio: {'compatible': ['i2c-gpio'], '#address-cells': 1, '#size-cells': 0, 'pinctrl-names': ['default'], 'pinctrl-0': [[68]], 'sda-gpios': [[46, 1, 0]], 'scl-gpios': [[46, 0, 0]], 'clock-frequency': 400000, 'status': ['okay'], 'rtc@68': {'compatible': ['dallas,ds1339'], 'reg': [[104]], 'status': ['disabled']}} is not of type 'array'
from schema $id: http://devicetree.org/schemas/gpio/gpio-consumer.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Rename touch to touchscreen.
Rename stmpe_touchscreen to touchscreen.
Rename stmpe_adc to adc.
Fix below CHECK_DTBS warning:
arch/arm/boot/dts/nxp/imx/imx7d-nitrogen7.dtb: touch@48 (ti,tsc2004): 'wakeup-gpios' does not match any of the regexes: '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/input/touchscreen/ti,tsc2005.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
